Crane Operations in Construction

Images of cranes and construction activities at significant sites, highlighting heavy equipment use in large-scale projects and construction management.

Raft with crane, Izmit, Turkey

LEED PROPELLANT PROJECT CONSTRUCTION PROGRESS - LAST WALL PUT UP

A crane lifts a Tainter gate into place at the U.S. Army Corps of Engineers, St. Paul District, Wild Rice Structure near Horace, North Dakota, Sept. 19. The gate is one of two that will be installed at the structure, which is a key component of the Fargo, North Dakota/Moorhead, Minnesota Metro Area Diversion project. Once the project is complete, it will reduce flood risk to more than 235,000 people within the region.

Preparations are underway to lift the bracket for the Orion Service Module Umbilical (OSMU) up for installation on the mobile launcher tower at NASA's Kennedy Space Center in Florida. The mobile launcher tower will be equipped with a number of lines, called umbilicals, that will connect to the Space Launch System rocket and Orion spacecraft for Exploration Mission-1 (EM-1). The OSMU will be located high on the mobile launcher tower and, prior to launch, will transfer liquid coolant for the electronics and air for the Environmental Control System to the Orion service module that houses these critical systems to support the spacecraft. EM-1 is scheduled to launch in 2018. The Ground Systems Development and Operations Program is overseeing installation of the umbilicals.

CAPE CANAVERAL, Fla. - The yellow framework seen here is the lifting fixture nicknamed the "Birdcage" that will have the ability to lift the Crew Module, or CM, and Launch Abort System, or LAS, assembly for the Ares I-X rocket and to stack and de-stack the assembly from the Service Module/Spacecraft Adapter assembly. It will also have the ability to lift and to stack and de-stack Stack-5 (all of the above components) from the Ares I-X in the Vehicle Assembly Building at NASA's Kennedy Space Center in Florida. Ares I-X is the test flight for the Ares I. The I-X flight will provide NASA an early opportunity to test and prove hardware, facilities and ground operations associated with Ares I. The launch of the 321-foot-tall, full-scale Ares I-X, targeted for July 2009, will be the first in a series of unpiloted rocket launches from Kennedy. When fully developed, the 16-foot diameter crew module will furnish living space and reentry protection for the astronauts, while their launch a

CAPE CANAVERAL, Fla. - Construction workers watch as a crane is used to lift the final large steel beam for installation on the base of the Mobile Launcher, or ML, at the Mobile Launcher Park Site at NASAs Kennedy Space Center in Florida. The ML is being modified and strengthened to accommodate the weight, size and thrust at launch of NASA's Space Launch System, or SLS, and Orion spacecraft.In 2013, the agency awarded a contract to J.P. Donovan Construction Inc. of Rockledge, Fla., to modify the ML, which is one of the key elements of ground support equipment that is being upgraded by the Ground Systems Development and Operations Program at Kennedy. The existing 24-foot exhaust hole is being enlarged and strengthened for the larger, heavier SLS rocket. The ML will carry the SLS rocket and Orion spacecraft to Launch Pad 39B for its first uncrewed mission, Exploration Mission-1, in 2018.

Construction workers weld steel beams to the second wing of the new 325th Force Support Squadrons new lodging facility at Tyndall Air Force Base, Florida, Nov. 10, 2022. The lodging facility will include 300 guest rooms, a restaurant, and a workout space.

The second section of the first half of the C-level work platforms, C South, for NASAs Space Launch System (SLS) rocket was offloaded from a heavy transport truck in a staging area on the west side of the Vehicle Assembly Building (VAB) at the agencys Kennedy Space Center in Florida. The Ground Systems Development and Operations Program is overseeing upgrades and modifications to VAB High Bay 3 to support processing of the SLS and Orion spacecraft. A total of 10 levels of new platforms, 20 platform halves altogether, will surround the SLS rocket and Orion spacecraft and provide access for testing and processing.

A damaged miter gate at Locks and Dam 14 on the Mississippi River in Pleasant Valley, Iowa, is lifted by the Quad Cities heavy-lift crane prior to being laid down on a barge for repair.

Raft with crane, Izmit, Turkey

CAPE CANAVERAL, Fla. - At NASA's Kennedy Space Center in Florida, construction continues on a new mobile launcher for the Constellation Program. The new mobile launcher will be the base for the Ares rockets to launch the Orion crew exploration vehicle and the cargo vehicle. The base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the added load of the 345-foot tower and taller rocket. When the structural portion of the new launcher is complete, umbilical lines, access arms, communications equipment and command/control equipment will be installed.

Crew Module Water Landing Model Assent Test site photos at Aberdeen Test Center (Aberdeen, MD)

A view of camera mounts installed on a Mark 35 Septar boat for the filming of Vandal Missile Operations. Base: Port Hueneme State: California (CA) Country: United States Of America (USA)

Shuttle T&R Offload Wind Restraint System Test

raines court construction shot

CAPE CANAVERAL, Fla. - At NASA's Kennedy Space Center in Florida, progress continues on the construction of a new mobile launcher, or ML, for the Constellation Program as a crane lifts the third section of the launcher's tower from the ground.Installation of the first section was on Sept. 24, and the second, on Oct. 15. The tower will have multiple platforms for personnel access and be approximately 345 feet tall. The launcher is being built at the mobile launcher park site area located north of Kennedy's Vehicle Assembly Building to support the Ares I rocket. The ML will provide a base to launch the Ares I, designed to transport the Orion crew exploration vehicle, its crew and cargo to low Earth orbit. The base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the heavier load of the tower and taller rocket.

SPLASH P1 Test 7 Swing Test: Documentation of preparation, set up and results of full scale BTA (Boilerplate Test Article) vertical drop test series performed in 2012 at the LaRC Hydro Impact Basin (HIB)

100 ton crane at the construction of the bridge. The extreme north. The polar night

The first of nine chemical steam generator (CSG) units that will be used on the A-3 Test Stand is hoisted into place at the E-2 Test Stand at John C. Stennis Space Center on Oct. 24, 2010. The unit was installed at the E-2 stand for verification and validation testing before it is moved to the A-3 stand. Steam generated by the nine CSG units that will be installed on the A-3 stand will create a vacuum that allows Stennis operators to test next-generation rocket engines at simulated altitudes up to 100,000 feet.

Assembly of the 105-metre-long light ring girder above the north stand of the Heinz Steyer Stadium

A construction fleet uses a crane-mounted drill do burrow holes into the current downstream concrete apron which will be filled with new concrete to form a secant wall at Montgomery Locks and Dam on the Ohio River in Monaca, Pennsylvania, Aug. 3, 2022. The U.S. Army Corps of Engineers Pittsburgh District manages the construction work at Montgomery, currently in the preconstruction phase. The current phase helps prepare the worksite for an upcoming multi-year construction project. Montgomery is part of the Upper Ohio Navigation Project, which has received $857.7 million in dedicated funding through the 2022 Infrastructure Investment and Jobs Act. The project will include replacing the facilitys 360-foot auxiliary chamber with a wider and longer 600-foot chamber that can fit up to nine barges at once. The district expects to begin work on the new lock construction in 2024, which will last at least eight years to complete.

CAPE CANAVERAL, Fla. - At NASA's Kennedy Space Center in Florida, construction is under way on a new mobile launcher for the Constellation Program. The new mobile launcher will be the base for the Ares rockets to launch the Orion crew exploration vehicle and the cargo vehicle. The base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the added load of the 345-foot tower and taller rocket. When the structural portion of the new launcher is complete, umbilical lines, access arms, communications equipment and command/control equipment will be installed.

CAPE CANAVERAL, Fla. - On Launch Pad 39B at NASAs Kennedy Space Center in Florida, the giant crane moves equipment that will be used to continue erecting the lightning towers. Each of the three new lightning towers will be 500 feet tall with an additional 100-foot fiberglass mast atop supporting a wire centenary system. This improved lightning protection system allows for the taller height of the Ares I compared to the space shuttle. Pad B will be the site of the first Ares vehicle launch, including Ares I-X which is targeted for summer of 2009, as part of NASAs Constellation Program.

SLS ENGINE SECTION PEDESTALS AND THE ENGINE SECTION SPIDER QUADRANTS ARRIVAL AND UNLOADING AT NASA DOCK ON THE TENNESSEE RIVER.

CAPE CANAVERAL, Fla. - A lightning mast remains to be lifted atop the third and final lightning tower erected on Launch Pad 39B at NASA's Kennedy Space Center. Three towers surround the pad. The new lightning protection system is being built for the Constellation Program and Ares/Orion launches. Each of the towers is 500 feet tall with an additional 100-foot fiberglass mast atop supporting a wire catenary system. This improved lightning protection system allows for the taller height of the Ares I rocket compared to the space shuttle. Pad 39B will be the site of the first Ares vehicle launch, including the Ares I-X test flight that is targeted for July 2009.

Large construction site

Exterior view of an F/A-18 Hornet aircraft hangar under construction. Base: Naval Air Station, Fallon State: Nevada (NV) Country: United States Of America (USA)

Two heavy-lift cranes are used to lower the Orion crew access arm onto a flatbed truck at Precision Fabricating and Cleaning in Cocoa, Florida. The crew access arm will be transported to a storage location near NASA's Kennedy Space Center in Florida. Later this month, the arm will be transported to the mobile launcher (ML) tower at the center. The crew access arm will be located at about the 274-foot level on the tower. It will rotate from its retracted position and interface with the Orion crew hatch location to provide entry to the Orion crew module. The Ground Systems Development and Operations Program is overseeing installation of umbilicals and launch accessories on the ML tower.

Crane on a building site, Hamburg, Germany, Europe

At Launch Pad 39B at NASA's Kennedy Space Center in Florida, construction workers position large segments of the support hardware for a new flame deflector in the flame trench. The new flame deflector will be positioned about six feet south of the shuttle-era flame deflectors position. During liftoff of NASAs Space Launch System, the rockets flame and energy will be diverted to the north side of the flame trench. The north side of the deflector will be protected by a NASA standard coating. The south side of the deflector will not be slanted and will have no lining. The new design will provide easier access for inspection, maintenance and repair. The Ground Systems Development and Operations (GSDO) Program at Kennedy is managing the installation of the flame deflector for Exploration Mission 1, deep space missions, and NASA's Journey to Mars.

CAPE CANAVERAL, Fla. - Ground support equipment technicians prepare one of the jacking, equalizing and leveling, or JEL, hydraulic cylinders for removal from crawler-transporter 1 at the crawler transporter maintenance facility at NASAs Kennedy Space Center in Florida. Sixteen new JEL hydraulic cylinders will be installed on CT-1 to increase load carrying capacity and reliability.The Ground Systems Development and Operations Program at Kennedy continues to upgrade CT-1 as part of its general maintenance. CT-1 could be available to carry commercial launch vehicles to the launch pad. The crawler-transporters were used to carry the mobile launcher platform and space shuttle to Launch Complex 39 for space shuttle launches for 30 years.

CAPE CANAVERAL, Fla. - In Launch Complex 39 at NASA's Kennedy Space Center in Florida, man and machine work side by side to position the walls of the Propellants North Administrative and Maintenance Facility.A tilt-up construction method is being used to erect a THERMOMASS concrete wall insulation system for the facility's walls. In this approach, the exterior layer of concrete for the wall panels is poured and leveled on the building's footprint. Then, prefabricated, predrilled insulation sheets are arranged on top of the unhardened concrete, and connectors, designed to hold the sandwiched layers of concrete and insulation secure, are inserted through the predrilled holes. Next, the structural wythe is poured. Once cured, these panels are lifted upright to form the building's envelope. The facility will have a two-story administrative building to house managers, mechanics and technicians who fuel spacecraft at Kennedy adjacent to an 1,800-square-foot single-story shop to store cr

Natural gas platform construction, Izmit, Turkey

Assembly of the 105-metre-long light ring girder above the north stand of the Heinz Steyer Stadium

View of the construction site, with the controlled load structure, as contractors end a load test, where a foundation pile successfully resisted a pressure of 225 tons, on Chièvres Air Base, Belgium, Aug. 28, 2022.

Crane of Cargo Ship with Pulp, Howe Sound, British Columbia, Canada.

CAPE CANAVERAL, Fla. -- Modifications continue on the Mobile Launcher, or ML, at the Mobile Launcher Park Site at NASAs Kennedy Space Center in Florida. Construction worker on lifts are preparing to cut and weld sections of the metal walls on the exterior of the ML. In 2013, the agency awarded a contract to J.P. Donovan Construction Inc. of Rockledge, Fla., to modify the ML, which is one of the key elements of ground support equipment that is being upgraded by the Ground Systems Development and Operations Program office at Kennedy. The ML will carry the SLS rocket and Orion spacecraft to Launch Pad 39B for its first mission, Exploration Mission 1, in 2017.

CAPE CANAVERAL, Fla. - At NASA's Kennedy Space Center in Florida, a crane maneuvers the seventh tower segment of a new mobile launcher, or ML, being constructed to support the Constellation Program, toward the six segments already in place, in the background at left.When completed, the tower will be approximately 345 feet tall and have multiple platforms for personnel access. The construction is under way at the mobile launcher park site area north of Kennedy's Vehicle Assembly Building. The launcher will provide a base to launch the Ares I rocket, designed to transport the Orion crew exploration vehicle, its crew and cargo to low Earth orbit. Its base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the heavier load of the tower and taller rocket.

Offshore Platform Construction

At Launch Pad 39B at NASA's Kennedy Space Center in Florida, a crane is used to move one of the large segments of the support hardware for a new flame deflector and position it in the flame trench. The new flame deflector will be positioned about six feet south of the shuttle-era flame deflectors position. During liftoff of NASAs Space Launch System, the rockets flame and energy will be diverted to the north side of the flame trench. The north side of the deflector will be protected by a NASA standard coating. The south side of the deflector will not be slanted and will have no lining. The new design will provide easier access for inspection, maintenance and repair. The Ground Systems Development and Operations (GSDO) Program at Kennedy is managing the installation of the flame deflector for Exploration Mission 1, deep space missions, and NASA's Journey to Mars.

Modifications continue on the Mobile Launcher, or ML, at the Mobile Launcher Park Site at NASAs Kennedy Space Center in Florida. Scaffolding, or work platforms, have been installed around the base of the tower on the ML to continue upgrades and modifications to the structure. The ML is being modified and strengthened to accommodate the weight, size and thrust at launch of NASA's Space Launch System, or SLS, and Orion spacecraft. The ML is one of the key elements of ground support equipment that is being upgraded by the Ground Systems Development and Operations Program at Kennedy. The ML will carry the SLS rocket and Orion spacecraft to Launch Pad 39B for its first uncrewed mission, Exploration Mission-1, in 2018.

KENNEDY SPACE CENTER, FLA. - At a radar site on North Merritt Island, Fla., one of two counterweights is being lifted for installation on a support structure (right) for a 50-foot C-band radar antenna dish. The radar will be used for Shuttle missions to track the launches and observe possible debris coming from the Shuttle. It will be used for the first time on STS-114. The launch window for the first Return to Flight mission is July 13 to July 31.

KENNEDY SPACE CENTER, FLA. -- Looking like a prehistoric monster crunching on its prey, the Caterpillar excavator and 48-inch shear attachment tear down Launch Umbilical Tower No. 1 (LUT-1) stored in the Industrial Area of KSC. The LUT-1 was part of the launch system used for Apollo-Saturn V, launching Apollo 8, Apollo 11, Skylab manned missions and the Apollo-Soyuz Test Project. The shear is one used in the deconstruction of the Twin Towers in New York City after 9/11.

SLS ENGINE SECTION PEDESTALS AND THE ENGINE SECTION SPIDER QUADRANTS ARRIVAL AND UNLOADING AT NASA DOCK ON THE TENNESSEE RIVER.

CAPE CANAVERAL, Fla. - At NASA's Kennedy Space Center in Florida, a crane lowers the third section of the tower for a new mobile launcher, or ML, for the Constellation Program toward the growing structure.Installation of the first section was on Sept. 24, and the second, on Oct. 15. The tower will have multiple platforms for personnel access and be approximately 345 feet tall. The launcher is being built at the mobile launcher park site area located north of Kennedy's Vehicle Assembly Building to support the Ares I rocket. The ML will provide a base to launch the Ares I, designed to transport the Orion crew exploration vehicle, its crew and cargo to low Earth orbit. The base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the heavier load of the tower and taller rocket.

DF-ST-88-02841. Base: Mcclellan Air Force Base State: California (CA) Country: United States Of America (USA)

Rolls of steel sheet in the harbor

KENNEDY SPACE CENTER, FLA. - On a radar site on North Merritt Island, Fla., part of the structure for the support base for a 50-foot C-band radar antenna is put in position. The radar will be used for Shuttle missions to track the launches and observe possible debris coming from the Shuttle. It will be used for the first time on STS-114. The launch window for the first Return to Flight mission is July 13 to July 31.

CAPE CANAVERAL, Fla. - At NASA's Kennedy Space Center in Florida, construction is under way on a new mobile launcher for the Constellation Program. The new mobile launcher will be the base for the Ares rockets to launch the Orion crew exploration vehicle and the cargo vehicle. The base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the added load of the 345-foot tower and taller rocket. When the structural portion of the new launcher is complete, umbilical lines, access arms, communications equipment and command/control equipment will be installed.

CAPE CANAVERAL, Fla. - Modifications continue on the Mobile Launcher, or ML, at the Mobile Launcher Park Site at NASAs Kennedy Space Center in Florida. A construction worker on a lift continues to cut through a section of a steel beam to prepare it for removal. The ML is being modified and strengthened to accommodate the weight, size and thrust at launch of NASA's Space Launch System, or SLS, and Orion spacecraft.In 2013, the agency awarded a contract to J.P. Donovan Construction Inc. of Rockledge, Fla., to modify the ML, which is one of the key elements of ground support equipment that is being upgraded by the Ground Systems Development and Operations Program office at Kennedy. The existing 24-foot exhaust hole is being enlarged and strengthened for the larger, heavier SLS rocket. The ML will carry the SLS rocket and Orion spacecraft to Launch Pad 39B for its first mission, Exploration Mission-1, in 2017.

CAPE CANAVERAL, Fla. -- At NASA's Kennedy Space Center in Florida, the rotating service structure (RSS) on Launch Pad 39B is being dismantled. Starting in 2009, the structure at the pad was no longer needed for NASA's Space Shuttle Program, so it is being restructured for future use. The new design will feature a "clean pad" for rockets to come with their own launcher, making it more versatile for a number of vehicles.

Belmar, N.J., Jan. 21, 2013 Powerful pile driving machinery hammers poles into the substrate during the recovery and rebuilding phase of the disaster caused by Hurricane Sandy. Through the Public Assistance (PA) Program, FEMA provides supplemental Federal disaster grant assistance for debris removal, emergency protective measures, and the repair, replacement, or restoration of disaster-damaged, publicly owned facilities and the facilities of certain Private Non-Profit (PNP) organizations. Adam DuBrowa/ FEMA. New Jersey Hurricane Sandy. Photographs Relating to Disasters and Emergency Management Programs, Activities, and Officials

SLS ENGINE SECTION PEDESTALS AND THE ENGINE SECTION SPIDER QUADRANTS ARRIVAL AND UNLOADING AT NASA DOCK ON THE TENNESSEE RIVER.

Stennis Space Center employees maneuver a new thrust measurement system in preparation for its installation on the A-1 Test Stand on March 3. The system was fabricated by Thrust Measurement Systems in Illinois and represents a state-of-the-art upgrade from the equipment used on the stand for more than 40 years. The A-1 Test Stand is being upgraded to provide testing for the next generation of rocket engines for America's space program.

Crane Lowering Pilings For Bridge Construction

Waldschlößchen Bridge

LEED PROPELLANT PROJECT CONSTRUCTION PROGRESS - WALLS GOING UP W/ CRANE

Dredger ship navy working to clean a navigation channel

SPLASH P1 Test 7 Swing Test: Documentation of preparation, set up and results of full scale BTA (Boilerplate Test Article) vertical drop test series performed in 2012 at the LaRC Hydro Impact Basin (HIB)

The Artemis I Orion crew module pressure vessel is loaded on NASA's Super Guppy plane in New Orleans for transport to Kennedy Space Center on Feb. 1, 2016. Part of Batch image transfer from Flickr.

Aufbau eines Windrades mit einem Spezialkran, Deutschland, Rheinland-Pfalz erecting a wind turbine with a special crane, Germany, Rhineland-Palatinate BLWS712154 *** Structure one Wind turbines with a Special crane, Germany, Rhineland Palatinate erecting a Wind Turbine With a Special crane, Germany, Rhineland Palatinate BLWS712154 Copyright: xblickwinkel/E.xTeisterx

At Launch Pad 39B at NASA's Kennedy Space Center in Florida, cranes lower large segments of the support hardware for a new flame deflector into place in the flame trench. Construction workers weld the structures together. The new flame deflector will be positioned about six feet south of the shuttle-era flame deflectors position. During liftoff of NASAs Space Launch System, the rockets flame and energy will be diverted to the north side of the flame trench. The north side of the deflector will be protected by a NASA standard coating. The south side of the deflector will not be slanted and will have no lining. The new design will provide easier access for inspection, maintenance and repair. The Ground Systems Development and Operations (GSDO) Program at Kennedy is managing the installation of the flame deflector for Exploration Mission 1, deep space missions, and NASA's Journey to Mars.

England, Devon, Bideford. A cargo ship being loaded with aggregate by a mobile crane on the quayside at Bideford Harbour.

Teams peform Orion Parachute Test Vehicle (PTV) loading operations on July 22, 2013 in preparation for the July 24 parachute drop test at the U.S. Army Yuma Proving Ground in Arizona. Part of Batch image transfer from Flickr.

Construction workers on the deck of the mobile launcher prepare the platforms for installation of vehicle support posts at NASA's Kennedy Space Center in Florida. At left, four of the support posts are installed. A total of eight support posts will be installed to support the load of the Space Launch System's (SLS) solid rocket boosters, with four posts for each of the boosters. The support posts are about five feet tall and each weigh about 10,000 pounds. The posts will structurally support the SLS rocket through T-0 and liftoff, and will drop down before vehicle liftoff to avoid contact with the flight hardware. The Ground Systems Development and Operations Program is overseeing installation of the support posts to prepare for the launch of the Orion spacecraft atop the SLS rocket.

Inside the Vehicle Assembly Building at NASAs Kennedy Space Center in Florida, operations are underway to attach a cover, called a spider, to the top of the Space Launch System (SLS) Core Stage pathfinder on Oct. 4, 2019. With the spider secured in place, a crane will be attached to it to lift the pathfinder into the vertical position. The 212-foot-long core stage pathfinder arrived on NASA's Pegasus Barge at Kennedys Launch Complex 39 turn basin wharf on Sept. 27, 2019. The Pegasus Barge made its first delivery to Kennedy in support of the agency's Artemis missions. The upgraded 310-foot-long barge arrived, ferrying the SLS core stage pathfinder, a full-scale mock-up of the rocket's core stage. It will be used by Exploration Ground Systems and its contractor, Jacobs, to practice offloading, moving and stacking maneuvers, using important ground support equipment to train employees and certify all the equipment works properly. The pathfinder will stay at Kennedy for approximately one

Cranes Lowering Poles On Construction Site

ORION Project-(SPLASH) Structural Passive Landing Attenuation for Survivability of Human Crew (BTA) Boiler Plate Test Article Water Impact Test-Pot Phase"0" Test Tested at the Hydro Impact Basin at the Landing and Impact Research Facility (Gantry)

Usa, Washington State, Seattle. Working at the Amazon Headquarters

A CREW INSTALLS A NEW EARTH SCIENCE RECEIVING SATELLITE ANTENNA OUTSIDE MARSHALL SPACE FLIGHT CENTER'S ACTIVITIES BUILDING 4316

CAPE CANAVERAL, Fla. -- Near the Vehicle Assembly Building at NASA's Kennedy Space Center in Florida, a crane offloads from a transporter one of the trusses, T4, to build the new mobile launcher for the Constellation Program. The new mobile launcher will be the base for the Ares rockets to launch the Orion crew exploration vehicle and the cargo vehicle. The base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the added load of the 345-foot tower and taller rocket. When the structural portion of the new mobile launcher is complete, umbilicals, access arms, communications equipment and command/control equipment will be installed.

What once was just a grass field nearly a year ago is now a construction site full of activity to lay the foundations of the Louisville VA Medical Center, in Louisville, Kentucky Sept. 9, 2022. The new 104-bed, full-service hospital located on Brownsboro Road in Louisville, Kentucky, will provide world-class healthcare for more than 45,000 Veterans in Kentucky and Southern Indiana.

SPLASH P1 Test 7 Swing Test: Documentation of preparation, set up and results of full scale BTA (Boilerplate Test Article) vertical drop test series performed in 2012 at the LaRC Hydro Impact Basin (HIB)

Salvage Engineering Response Team - New Orleans - Boats - 26-HK-349-47. OB 131. Hurricane Katrina

Mobile crane makes emergency operation on a motorway. Move container cargo.

SPLASH BTA Phase 2 Vertical Tests 9: Documentation of preparation, set up and results of full scale BTA (Boilerplate Test Article) vertical drop test series performed in 2012 at the LaRC Hydro Impact Basin (HIB)

Hurricane Katrina

CAPE CANAVERAL, Fla. - New windows are installed in the Launch Control Center's Firing Room 1 at NASA's Kennedy Space Center in Florida. The firing room will support the future Ares rocket launches as part of NASA's Constellation Program. Future astronauts will ride to orbit on Ares I, launched from Kennedy's Launch Pad 39B. The Launch Control Center firing rooms face the launch pads.

The Walney Offshore Windfarm project is located 15km off Barrow in Furness in Cumbria. The project consists of Walney 1 and Walney 2 each with 51 turbines. When finished, it will

ORION Project-(SPLASH) Structural Passive Landing Attenuation for Survivability of Human Crew (BTA) Boiler Plate Test Article Water Impact Test-PIT Test-2Tested at the Hydro Impact Basin at the Landing and Impact Research Facility (Gantry)

Construction workers assist as a crane lifts the Core Stage Forward Skirt Umbilical into position for installation on the mobile launcher tower at NASA's Kennedy Space Center in Florida. The mobile launcher tower will be equipped with a number of lines, called umbilicals that will connect to the Space Launch System (SLS) rocket and Orion spacecraft for Exploration Mission-1 (EM-1). The CSFSU will be located at about the 180-foot level on the tower, above the liquid oxygen tank. The CSFSU is an umbilical that will swing into position to provide connections to the core stage forward skirt of the SLS rocket, and then swing away before launch. Its main purpose is to provide conditioned air/GN2 to the SLS core stage forward skirt cavity. The Ground Systems Development and Operations Program is overseeing installation of the umbilicals.

Heavy Construction Equipment And Pilings For Bridge

Installing fume extraction pipe into steel foundry smelter

special crane equipment working for global road reconstruction

Work continues on the site of the new Louisville VA Medical Center in Louisville, Kentucky Oct. 31. Structural steel placement began recently as placement of concrete for the basement walls and earthwork continue on the site. The new 104 bed, full-service hospital, will provide world-class healthcare to more than 45,000 Veterans. Construction is anticipated to be completed in 2026.

A crane prepares to lower the first-in-class aircraft carrier USS Gerald R. Fords (CVN 78) aircraft crash handling and salvage crane onto the flight deck, Jan. 17, 2023. Ford is in port at Naval Station Norfolk for a continuous planned maintenance availability.

Maintenance and Logistics Commands Atlantic - Property Inventory Team - Station Pascagoula - 26-HK-193-7. Hurricane Katrina

Construction workers with JP Donovan monitor operations as a crane is used to lower the first of two Tail Service Mast Umbilicals for installation on the 0-level deck of the mobile launcher on July 12, at NASA's Kennedy Space Center in Florida. The 35-foot-tall umbilical will connect to NASA's Space Launch System rocket core stage aft section and provide liquid oxygen and electrical cable connections to the core stage engine section to support propellant handling during prelaunch operations. The installation brings Exploration Ground Systems one step closer to supporting prelaunch operations for the agency's SLS rocket and Orion spacecraft on Exploration Mission-1 and deep space destinations.

Construction site wka_05.tif construction site for the construction of a new wind turbine, Witten, Ruhr area, North Rhine-Westphalia, Germany, Europa

CAPE CANAVERAL, Fla. -- At NASA's Kennedy Space Center in Florida, the 600-Ton Test Fixture outside the Launch Equipment Test Facility conducts a 500,000-pound pull test of a bridge crane lifting element, which is used to lift space shuttles in the Vehicle Assembly Building. The fixture proofload tests, in tension and compression, a variety of ground support equipment, including slings, lifting beams and other critical lifting hardware that require periodic proofloading.Since 1977, the facility has supported NASAs Launch Services, shuttle, International Space Station, and Constellation programs, as well as commercial providers. The facility recently underwent a major upgrade to support even more programs, projects and customers. It houses a 6,000-square-foot high bay, cable fabrication and molding shop, pneumatics shop, machine and weld shop and full-scale control room. Outside, the facility features a water flow test loop, vehicle motion simulator, launch simulation towers and a c

Nearly three years after the Fort Meade Museum closed a contractor team moved a Liberty Mark VII from the vacated building April 18-19, 2022. The Liberty Mark VIII and an M3A1, which was also removed from the museum, will become part of the U.S. Army Armor & Calvary collection housed in the Armor Training Support Facility at Fort Benning, Georgia.

N-206 NASA Ames Research Center 12ft w.t. Pressure Wind Tunnel reconstruction - turning vanes, fan being lifted in

CAPE CANAVERAL, Fla. - At Launch Pad 39B at NASAs Kennedy Space Center in Florida, construction workers continue to remove the flame trench deflector that sits below and between the left and right crawlerway tracks.Launch Pad 39B is being refurbished to support NASAs Space Launch System and other launch vehicles. The Ground Systems Development and Operations, or GSDO, Program office at Kennedy is leading the centers transformation to safely handle a variety of rockets and spacecraft.

Under the watchful eye of technicians and engineers, a crane is prepared to lift the Orion crew access arm (CAA) so it can be attached to the mobile launcher (ML) at NASA's Kennedy Space Center in Florida. The arm will be installed at about the 274-foot level on the ML tower. NASA's Exploration Ground Systems organization has been overseeing installation of umbilicals and other launch accessories on the 380-foot-tall ML in preparation for stacking the first launch of the Space launch System, or SLS, rocket with an Orion spacecraft. The CAA is designed to rotate from its retracted position and line up with Orion's crew hatch providing entry for astronauts and technicians.

Work continues on a sanitary tank in the southwest portion of the site of the Louisville VA Medical Center Feb.7, 2024.

Vehicle Assembly Building and Launch Pad Supports

CAPE CANAVERAL, Fla. - At NASA's Kennedy Space Center in Florida, the tower on a new mobile launcher, or ML, for the Constellation Program grows as the fourth section is lowered into position.The tower will be approximately 345 feet tall when completed and have multiple platforms for personnel access. The ML is being built at the mobile launcher park site area north of Kennedy's Vehicle Assembly Building. The launcher will provide a base to launch the Ares I, designed to transport the Orion crew exploration vehicle, its crew and cargo to low Earth orbit. The base is being made lighter than space shuttle mobile launcher platforms so the crawler-transporter can pick up the heavier load of the tower and taller rocket.

The construction area for a future transient training brigade headquarters in the 1600 block on the cantonment area is shown Jan. 5, 2023, at Fort McCoy, Wis. A contract, totaling $11,964,432.87, was awarded June 9, 2022, to L.S. Black Constructors to build the fiscal year 2022 Transient Training Brigade Headquarters project at Fort McCoy. Construction operations began in August 2022. Location of construction is just across the street from where the same contractor has been building two new transient training troop barracks buildings in the same block. According to the Fort McCoy Directorate of Public Works, the brigade headquarters project is based on the denser, more consolidated footprints of Fort McCoys Troop Housing Area Development Plan. The project will include the latest, state-of-the-art systems for fire protection and alarms and video surveillance as well as Energy Monitoring Control Systems. Also, anti-terrorism and force protection measures will be incorporated. And through

The Brownlee Barge Crane, a non-self-propelled, barge-mounted crane with spuds, is based in New Orleans, Louisiana. The 170,000 lbs. capacity ringer crane mission is to assist in maintenance and gate repairs for South Louisianas locks along the Intercoastal Waterways.

Abriss des Hochsilo in Mölln Abriss des Hochsilo in Mölln Copyright: xZoonar.com/Zoonar.com/zoonar/MarkusxHötzelx 22924007

SPLASH P1 Test 7 Swing Test: Documentation of preparation, set up and results of full scale BTA (Boilerplate Test Article) vertical drop test series performed in 2012 at the LaRC Hydro Impact Basin (HIB)

of 3